Productos > EPoX Series > 2E10-110-TX-V2

2E10-110-TX-V2

1-Port EPo2 TX Adapter with 802.3af/at/bt PoE++ Output

La descripción general

AETEK EPo2(Ethernet & Power over 2 wires) kit allows you to connect PoE IP devices such as Intercom/Access Control/ Speaker/Touch Screen Station/VoIP/sensor/camera over in-wall doorbell wire, telephone line or 2 conductor cable to Ethernet network. You don’t have to configure anything, and you only need one AETEK EPo2 unit at each end of PoE IP device(PD) & Ethernet Switch port. In addition to reuse 2-wire cable, AETEK EPo2 is designed to extend PoE range & data rates far beyond 100meters/100 Mbps limits even using 2-wire thinness 26AWG cable.

+ AñadirALaListaDeConsultas DocumentoDeDescargar

Características principales

  • Uses telephone line, doorbell wire or 2 conductor cable to
  • connect PoE IP devices
  • Plug-and-Play deployments
  • Reuses in-wall 2 wires infrastructure
  • Optional 19 inch 8-bay rack mount chassis (CH-110-V2)
  • Support IEEE 802.3 bt/at/af PoE output

Aplicación

Accessories

EPo2 RX Adapter

EPo2 RX Adapter
2E11-110-RX-V2 2E10-110 EPo2 adapter(RX)
65W@56VDC power adapter

EPo2 TX Adapter

EPo2 TX Adapter
2E10-110-RX-V2 2E11-110 PoE EPo2 adapter(RX)
Supports 30W/60W/90W PoE Input

Accessories

Accessories
PA-150-065 100 ~ 240 VAC input 56VDC/65W output

Specifications comparison

Model
2E10-110-TX
2E10-110-TX-V2
2 PIN Terminal Block
1
1
10/100Mpps Ethernet RJ45
1
1
Transmission mode
TX mode
TX mode
Power Output
Passive PoE (IEEE 802.3af compliant)
IEEE 802.3af/at/bt PoE++
PoE Pass Through
v
v

Especificación

Interface / Distance
EPo2 Ports
2-Pin Terminal Block x1
10/100 Mbps Ethernet
PoE PSE RJ45 x 1
Transmission mode
Transmitter TX mode
MAX. (Power+Data) Distance
Maximum 600m with data and
power depending on cable gauge AWG
Cable Type
Doorbell wire 18/20/22 AWG
Telephone cable 24/26AWG
2 Conductor cable: 23/24AWG
Data Rate
2 wires: Up to 100 Mbps asymmetrical to full range
Ethernet cable: 100 Base-TX full duplex
Power
Power Input
PoE over 2 wires shielded cable
DC power jack: 56VDC
PoE Output
IEEE 802.3bt PoE++ PSE
IEEE 802.3at PoE+ PSE
IEEE 802.3af PoE PSE
Unit Power Consumption
2W
Mechanical
Dimensions (W x D x H)
85.4 x 47.1 x 27.0 mm (3.36 x 1.85 x 1.06")
Weight
0.2 kg (0.44 lb)
Connectors
2P Terminal Blockx1, RJ45 x1, DC Jack x1, PoE On/Off Switch x1
Mounting Type
Wall mount, Din-rail (optional)
Casing
Metal
Join Button
1~3 sec.: Link RX and TX
5~8 sec.: Disconnect RX and TX
10~15 sec.: Reset to default
Environmental
Operating Temperature
-20°C ~ 60°C (-4°F ~ 140°F)
Storage Temperature
-20°C ~ 85°C (-4°F ~ 185°F)
Operating Humidity
5% ~ 95% non-condensing
Certifications
EMC
CE, FCC, VCCI, C-Tick
Safety
EN62368-1
LEDs
POE
PoE status
LAN
Ethernet status
PWR
Power status
LINK
EPo2 RX and TX connection status